Geovision GV-AS110 User Manual Page 83
- Page / 255
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
GV-AS120 Controller
65
3
3.2.3 Connecting Output Devices
GV-AS120 supports 1 type of output: Door outputs, e.g. electronic lock
The table below shows the wire assignments of output connectors on GV-AS120.
Wire color Definition
Purple Door COM
Orange Door NC
Gray Door NO
Check if your output device meets the following absolute maximum ratings before
connecting it to the Door outputs.
Breakdown Voltage
250V AC, 220V DC
Continuous Load Current
1A (30V DC), 0.3A (125V AC)
Note: Absolute Maximum Ratings are those values beyond which damage to GV-
AS120 circuit board may occur. Continuous operation of GV-AS120 at the absolute
rating level may affect GV-AS120’s reliability.
To connect an output device:
The example below illustrates the connection of a locking device to GV-AS120. Connect the
(+) point on the locking device to the Door COM wire on GV-AS120, connect the two (-)
points of the locking device and the external power supply together, and connect the (+)
point on the external power supply to the Door NO or Door NC wire on GV-AS120 based on
the state of the locking device.
Figure 3-5
- GV-AS/EV Controller 1
- Contents 3
- Welcome 10
- Elevator Control 13
- Optional Devices 14
- Installation Considerations 16
- Definition 18
- 1.1 Introduction 20
- 1.1.1 Main Features 22
- 1.1.2 Packing List 23
- 24
- GV-AS100 GV-AS1010 24
- Figure 1-4 24
- 1.2 Installation 25
- 1.2.1.B RS485 Readers 27
- 1.2.4 Connecting the PC 32
- 1.2.5 Connecting the Power 35
- 1.2.6 Fitting the Battery 36
- 1.3 Programming Mode 38
- 1.3.2.A Adding a Card 42
- 1.3.2.B Deleting a Card 43
- 1.3.5 Setting Parameters 45
- Control Type: 46
- 2.1 Introduction 53
- 2.1.1 Main Features 55
- 2.1.2 Packing List 56
- 2.2 Installation 57
- GV-AS1110 58
- 2.2.4 Connecting to the PC 63
- 2.2.5 Connecting the Power 65
- 2.3 Programming Mode 66
- 2.3.1.A Adding a Card 67
- 2.3.1.B Deleting a Card 68
- 2.4 LED Status and Beeper 72
- 3. GV-AS120 Controller 77
- 3.1 Introduction 78
- 3.1.1 Main Features 80
- 3.1.2 Packing List 80
- 3.2 Installation 81
- 3.2.4 Connecting to the PC 84
- 3.2.5 Connecting the Power 86
- 3.3 Programming Mode 87
- 3.3.1.A Adding a Card 88
- 3.3.1.B Deleting a Card 88
- 3.4 LED Status and Beeper 89
- 3.6 GV-AS120 Specifications 91
- 4.1 Introduction 93
- 4.2 Installation 95
- 4.2.1.B RS-485 Readers 96
- 4.2.5 Connecting the Power 99
- 4.2.6 Connecting the PC 100
- GV-AS2110 101
- 4.3 Other Settings 102
- Power Jack 103
- 4.4 The Web Interface 104
- 5. GV-AS400 Controller 106
- 5.1 Introduction 107
- Wiegand A Wiegand B 108
- Wiegand C 108
- Wiegand D 108
- Wiegand E Wiegand F Wiegand G 108
- Wiegand H 108
- 5.2 Installation 109
- 5.2.1.A Wiegand Readers 110
- 5.2.1.B RS-485 Readers 111
- 12345678 112
- 5.2.3.A Outputs 1 ~ 8 113
- 5.2.3.B Outputs 9 ~ 16 114
- 5.2.4 Connecting the Power 116
- 5.2.5 Connecting the PC 117
- 5.2.7 Fitting the Battery 119
- 5.3 Other Settings 120
- 5.4 The Web Interface 122
- 5.5 Optional GV-ASKeypad 123
- 5.5.2 Operation 124
- 5.6 GV-AS Power Board 126
- 5.6.3 Connecting the Power 128
- 5.7 GV-AS400 Specifications 130
- 6.1 Introduction 132
- 6.2 Installation 134
- 6.2.1.B RS-485 Readers 135
- 6.2.5 Connecting the Power 139
- 6.2.6 Connecting the PC 140
- 6.3 Other Settings 141
- 6.4.1 Packing List 143
- 6.4.2 Overview 143
- Power Adapter Board 145
- 6.5 The Web Interface 147
- 7. GV-EV48 Controller 149
- 7.1 Introduction 150
- 7.1.3 GV-EV48 Board Layout 151
- 7.2 Installation 152
- Elevator 153
- Control Panel 153
- 7.2.4 Connecting the Power 154
- 7.2.5 Connecting the PC 155
- 7.3 Other Settings 156
- 7.4 The Web Interface 158
- 7.5 GV-EV48 Specifications 159
- 8. Installing on a Network 160
- 8.1 Fixed IP Connection 162
- 8.2 DHCP Connection 164
- Connection over Internet 167
- 9. The Web Interface 170
- 9.1 Basic Settings 172
- 9.1.2 Upgrading Firmware 174
- 9.2 Advanced Settings 177
- 9.2.1 Function Setting 179
- 9.2.2 Parameter Setting 182
- 9.2.2.B GV-EV48 186
- 9.2.3 Card Setting 188
- 9.2.4 Card Information 189
- 9.2.5 Time Setting 190
- 9.2.6 Input Setting 192
- 9.2.7 Output Setting 195
- Output Type 196
- Output Function 196
- Output Conditions 196
- 9.2.8 Wiegand Function 201
- 9.2.9 Function Key 202
- 9.2.10 Urgent Card 203
- 9.3 Extended Device 204
- 9.3.2 Extended I/O 207
- 10. Optional Devices 208
- 10.1 Optional GV-ASBox 209
- Figure 10-1 210
- 10.1.4 Installation 211
- Output Device 216
- External Power 216
- 10.1.4.G Other Settings 218
- 10.2 Optional GV-ASNet 220
- 10.2.3 GV-ASNet Overview 221
- 10.2.4 Installation 222
- 10.2.4.D.c Power Status LED 225
- 10.3.1 Basic Setting 227
- 10.3.2 Advanced Settings 228
- 10.3.2.A Function Setting 229
- 10.3.2.B Parameter Setting 232
- 10.3.2.C Status Monitor 236
- 10.3.2.D Card Information 237
- 10.3.2.E Time Setting 238
- 10.3.2.F In/Out Function 239
- [Output Function] 241
- 10.3.2.G Extended Reader 246
- 11. Troubleshooting 248
- Internet 249
- Appendix 254
- (Optional) 255
© 2020, manymanuals.com. All rights reserved. | 0.660 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals